Sunday, July 27, 2014

INSTALLING THE BATTERY MODULE WAS QUITE A SHOCKING EXPERIENCE!

Today I was out working on the Fiero by 7 am and had to finish the outboard end plate. The wire feed welder I have is a cheap Harbor Freight Chicago Electric Welding model with a 10% duty cycle, so after welding for a minute, you have to wait 9 minutes for it to cool down. After tack welding the clips in place and marking where the holes to bolt down the tie straps, the end plate was removed. When starting to drill the holes that were going to be tapped, both of the clips broke loose, so the end plate had to be bolted on the module again and better tack welds re-applied. 

Finally, all of the clips were welded in place, the holes drilled, the plate ground, to clean off all of the splatter, and a coat of paint applied, so it was time to start putting the first cell in place. The leads from the existing battery pack in the front of the car were in the way so I had to disconnect them. When working the first cell with the end plate and the rods, my arm came in contact with the negative terminal and I got quite a shock, so stopped and taped both of the leads. It had rained and I had left the trunk lid open, so there was a bit of water inside the engine compartment. I have been chasing a ground leak but have not found it yet, so it will be interesting to see if it goes away with the new module installed. With the rods inserted through the end plate and a cell, it was a struggle getting the hold down clips to go over the battery rack angle iron but with some twisting and prying, finally got both of them over the angle. Then I started the second cell on the rods and started working it toward the outboard side of the car to mate with the first cell. I am going to have to move the controller about a half an inch for the cells to clear it but was able to work the second cell around the protruding fan housing to slide it toward the first cell. My arm came in contact with the negative terminal of the controller and again I was shocked! I really don't understand this, as the leads were disconnected from the controller and the positive pack voltage lead was disconnected. Also the contactor on the positive lead of the battery was de-energized, so there should not have been any voltage there.


GETTING SHOCKED!

I would have disconnected the battery terminals on the battery pack in the front of the car but the Allen socket that I needed was no where to be found. I had a set that fold out but none of the sizes were correct. It slipped out of my hand and created a ball of fire when it contacted the negative and positive terminals, so the negative terminal of the controller was just taped so I could continue installing the cells. As my luck would have it, just as I was getting ready to put in the third cell, there was a giant clap of thunder and after getting shocked twice and shorting the battery pack terminals, decided it is time to pack it in for the week, as about the only thing left was to get struck by lightning!

Still looking for a tow dolly on Craigs List but the only seller to respond was too far away, so the search continues.

EVCCON or Bust!

Randy

Saturday, July 26, 2014

FABRICATING BATTERY MODULE HOLD DOWN CLIPS

The pack is going through the final bottom balance with the JLD404 set up to turn on a small flash light bulb at 2.7 volts and then discharge until the battery reaches 2.5 volts. The cells all seem to have pretty much settled out at just under 2.7 volts.

While bottom balancing the cells, I am fabricating steel end plates and have welded clips on the plate to hold down the module. On the inside plate, the angle is long enough that holes will be drilled and the plate bolted down to the support angles. I wrote about them it the last post but here is the completed inboard end plate.


INBOARD MODULE END PLATE

On the outboard side of the module, the end of the angle used to make the rack is not long enough to bolt the clips, so the clips will be turned around and will hook under the rack angle. Below is a rough diagram and a picture of the cell in place to confirm that the clips will hook the end of the angle.



OUTBOARD HOLD DOWN CLIP DIAGRAM


CELL WITH CLIPS UNDER RACK ANGLE

With any luck I will be able to start mounting the module tomorrow, if I can find a metric tap to thread the holes for the tie bars.

Thanks for visiting,

Randy

Wednesday, July 23, 2014

BATTERY RACK

This morning the Fiero was taken to Gary's Place, a local mechanic in Kirkersville, but not before having to mess with the controller. The laptop had to be hooked up so the pot box could be re-calibrated. Once that was done the car ran flawlessly the 3 miles to the shop. The HiPower cells seem to be sagging less and as soon as I let my foot off the accelerator, the voltage came right back up to 124 volts.

The car was driven up on the lift and once off the ground, we started measuring and figuring where to place the angle. Once under the car, it became apparent we could mount the rack to the cradle without having to weld anything to the firewall or sides of the engine compartment. The front angle was placed completely across from the drivers side to the passenger side.of the cradle and the rear angle was run about 25 inches and terminated just before it came in contact with the motor adapter. The module is 23 inches long, with the existing end plates, so with the new thinner steel end plates I am making, will be less..


BATTERY RACK


CELL PLACEMENT TEST

Angle clips will be made and welded to the bottom of the new steel plates and will bolt to the angles, to hold the pack in place. There will be four, 3/8 inch bolts and fender nuts will be used so the bolts will be able to just be screwed in, without having to put a wrench on the bottom.




HOLD DOWN ATTACHMENTS


HOLD DOWN ATTACHMENT DETAIL


BATTERY RAIL ATTACHMENT

Thanks for visiting,

Randy

Monday, July 21, 2014

STEERING WHEEL, SEATS, AND CONSOLE - INTERIOR NEARING COMPLETION

Work is continuing on getting the USB charging set up to power the Dell Venue 8 Pro and a button has been located that will short the data leads until the charger starts on the tablet. The tablet did start charging when the cable went only to the charge port, but when a Y was connected with a mouse, the tablet did not start charging, so still working on the details.


USB CHARGE ENHANCER

A Panel has been fabricated to mount the JLD404 and the USB button but I am still working on a way to properly mount the button. Once the meter and button are mounted, the center console will be able to go back in the car. Also, I found a volt, amp, amp hour and watt hour meter on EBAY, so it may be used instead of the JLD404, as tracking watt hours would be a little more accurate way of measuring the charge than amp hours.


VOLT, AMP, AMP HOUR, WATT HOUR METER

The steering wheel cover has been sown on and the wheel mounted back in the car, so no more vice grips to steer the car when having to move it.


STEERING WHEEL COVER INSTALLED

The new seats that came with the car were removed from storage and cleaned. a bolt was missing from one of the brackets, so one was robbed from the original seats. Upon closer inspection, the seats were in much better condition that I remembered and the solid charcoal gray will look good in the Fiero.


BETTER SEATS

The Better Place Module that is being bottom balanced is getting close to being finished and once the individual cells have all settled under 2.7 volts, will be charged to about 2.75. This will require manually stopping the charger at 2.75 volts as the lowest setting on the Powerlab 6 is 3 volts. The Powerlabs are good but could be so much better if Revolectrix would offer a different firmware package for EV use than is currently available for the RC crowd.


POWERLAB 6

I have decided to take a week off work next week to fix the back porch steps, install a new front storm door, and try to make some progress on the Fiero. I have an offer to tow the Fiero to EVCCON and I am really close to having it ready in time, so will try to find a way to get one of the Better Place modules mounted. I sent an email about a towing dolly on Craigslist but have not heard back from the seller, so it may already have been sold.


NEW STEPS FINISHED


FINDING A SPACE FOR A MODULE

Tomorrow I am going to paint the new steps and back porch floor, then start on the new storm door. It is supposed to get up in the 90's in Ohio, so I am planning on starting early and finishing up in the evening when it starts cooling down a little. Hopefully there will be some time in there to start fabricating the angle iron to hold the Better Place Module. I may check with a local mechanic, who has a lift and is a pretty good welder, to see how busy he is. If he doesn't have much going on, he may be able to help get the Better Place Modules mounted.

Until next time,

Randy

Sunday, July 13, 2014

SETTING UP THE POWERLAB 6 AND 8


A while back, I smoked my Powerlab8 battery charger, so bought a reconditioned Powerlab6 to assist in bottom balancing the Better Place Module. After setting it up, I was not able to discharge down to 2.7 volts and kept getting a warning that the cell is under 3 volts. I posted on the EVTV Forum and a couple of EV builders have posted Youtube videos on how they set up their Powerlabs to bottom balance









After watching the videos, I found the regenerative discharge was not checked and after it was checked, the Powerlab 6 would do a discharge only, even when below 3 volts.

More measurements were taken to try and figure out where to put the Better Place module and a plate was made to cover the radio opening to mount the JlD404.  There will also be a switch that turns on a USB charge enhancer, that increases the power and shorts the data leads. This should allow the Venue 8 to start charging when it boots up and once the charger starts, the data leads can be un-shorted to allow the tablet to communicate with the Synkromotive controller. I will post some pictures when the plate is closer to being finished. Also, the steering wheel cover was sown up making it ready to go back in the car and the new wiring harness was run through the center console.

Probably will not get the car back on the road in time to take it to EVCCON but am going to keep pushing and see where I end up.

Randy

Saturday, July 5, 2014

DEW WIPES AND DOOR PANELS DONE!

When I read the write up on how to replace the outer door window seals (dew wipes) they said the second one was easier that the first, and they were correct. Around 9 am the passenger side door was started, and proceeded very well. I did have a bit of a time getting the screws behind the window glass to break loose with the tool I made after seeing one on Rodney Dickman's website.


OLD AND NEW GLASS SEALS AND TOOLS

Newspaper was folded and stuffed in the space between the window glass and the outer side of the door, to keep the screw from going all the way to the bottom of the door, if it was dropped, and saved me a lot of work when one of them dropped. I was able easily get it off of the paper with a magnet. When putting the new dew wipe in, I did run into problems with one of the screws behind the glass. Finally I was able to use a punch and tap the seal toward the hinge side of the door, finally lining up the hole. By early after noon, the door was assembled except for the panel. The panel, arm rest, and door handle cover were painted with interior paint and the second door was finished.


OUTSIDE VIEW OF NEW DEW WIPE


REFINISHED PASSENGER DOOR PANEL

That was it for work on the Fiero on Saturday, as it was time for mowing and trimming the grass but felt good about the progress that was made over the last two days.


Until next time,

Randy

Friday, July 4, 2014

JULY 4TH

Today, work on the driver's side dew wipe started around 8 am, and it was still only in the high 50's in Columbus, Ohio. The window was rolled down and I was able to get 3 of the screws holding the dew wipe and the side mirror screws out but the other 2 screws were blocked by the window glass. The night before, I had made a screw driver that is supposed to be able to remove them, but the screws would not break loose. Tired of messing around and not wanting to drop the window guide, I was able to get a hack saw blade behind the dew wipe and just cut the screw off. I went to Advance Auto Parts and picked up some molding adhesive, deciding to just glue the center of the dew wipe in place.  After the new dew wipe was attached in place with the outside and mirror screws, I put wooden wedges in the center of the dew wipe and applied molding adhesive between the dew wipe and the door flange. Wood wedges were put between the dew wipe and window to keep pressure on the piece until the adhesive dried. Then the rubber seals and inner dew wipe were bolted on. Finally the door panel, arm rest, and door handle cover were installed to finish the job. While the door panel was off, the tracks were lubricated as much as was possible so the squeak that was previously heard when the window was run up, was now gone.


INSIDE VIEW OF DOOR PANEL


OUTSIDE VIEW OF NEW DEW WIPE

The new steering wheel cover has not been stitched yet, so I decided to paint the exposed hub and spokes with black truck bed liner to give it some texture.


STEERING WHEEL PAINTED

After the steering wheel was drying, some more measurements were taken of the lower trunk and it looks like the Better Place Module will fit there, while still allowing the upper portion to be open for luggage or groceries.  Having cleaned the trunk out last week, and having most of a can of truck bed liner left from painting the steering wheel, the trunk was given a coat..


TRUCK BED LINER APPLIED TO TRUNK

My son and his fiance came over in the evening and we had steak, shrimp, and chicken shish sabobs on the grill. We found a box of fire works left over from when my son worked at Phantom Fireworks, so will have a display out in the back yard tonight. We were invited to my parent's for a cook out also but my wife's back has been bothering her and we did not want to go without her, so decided to just cook out at home. After a hard day of work on the Fiero, it was nice to kick back in the afternoon and relax a little.