FIXING THE METER WIRING

Last week I put the center console back in the Fiero but when trying to make up the connections to the panel meters, found that a couple of the connectors were wired wrong. I had the 12 volt power wires going to the panel meter shunt wires. There were two wires connected, that I just could not remember where they came from, so today, measured them with a volt meter and found they increased in millivolts as the interior lights were turned on, then increased more when the headlights were turned on, so reasoned that those were actually the 12 volt shunt wires. 

The 12 volt panel meter is not lighting up, so I removed it and checked it across a 12 volt battery. It came on just fine, so went inside the car to run voltage checks on the power feed wires. When the power was originally connected, 12 volt wires branched off, to go to each of the panel meters. The pack voltage meter is working just fine but I do not have 12 volts coming out of the low voltage meter dc-dc converter, so deduct that it went bad. I will need to order another one from Light Object so hopefully this will solve the problem and the instrument panel can be closed back up.

PANEL METER DC-DC ISOLATION CONVERTERS

The pack voltage and shunt wires were connected and when the motor was revved up, I got a current reading. The meter is a 100 amp scale with a 100 amp/75 mv shunt, so  with the 1000 amp/75 mv shunt, I just need to multiply the reading by 10. I searched for a 200 volt 1000 amp duel panel meter but could not find one anywhere, so figured this arrangement would give me an indication of the amps being pulled. I am a little worried because when I switched power to the controller, there was a loud pop in the rear of the car. The motor spun normally and when I went back to investigate, nothing could be found. The Synkromotive Controller is supposed to have built in pre-charge but maybe I still need to wait a little longer before switching the switch all the way to the start position. 

A TCCH charger was purchased on EBAY, as the Pic Chip for the Zivan NG3 charger, would not turn the charger on. I was a little disappointed when when the TCCH charger arrived as it is a good 10 pounds heaver and shutting off at 137 volts, is only rated at 20 amps. The NG3 is rated at 18 amps at 137 volts so I am not gaining that much going to the much heavier charger. I also ordered an AC contactor and will use it as a fail safe, to shut the charger off at 137 volts.

TCCH 3000 CHARGER

To warm the interior of the Fiero, a spot light was put inside overnight, so it would be warm when I started working on the wiring, It worked really well and I was perfectly comfortable working on the wiring, even though the garage was in the 40s.

SPOT LIGHT INTERIOR HEATER

Awhile back I hooked up a TV to keep me company while bottom balancing the modules, so spent the day working on wiring and watching Superbowl coverage. I didn't end up watching much of the actual game but did get to see the final Sea Hawk drive end with the interception on the goal line.

TV TO KEEP ME COMPANY

Spring is just around the corner and if I can get the meters working, the interior back together and the battery charger back in the car, will be able to start driving it in a month or so. I want to get a belly pan back on the car before it is driven in rain or snow but will take it over to a mechanic with a lift in Kirkersville and have him help me put it back on the car. The previous owner claimed that it dropped the amp draw significantly, then the car is driven on the interstate.

Until next post,

Randy 

METERS, METERS.....AND MORE METERS!

The 12 volt system Volt/Amp Meter was hooked up and was reading current and voltage just fine, so I decided to hook up the traction pack meter. The 12 volt system meter was hooked up to the isolated side of the 12 volt dc-dc isolation converter, so it was disconnected and hooked up to the un-isolated side. The meter came on and read voltage just fine but read zero amps. It seems that both meters will need to run off of an isolation 12 volt dc-dc converter, so another one was ordered from Light Object. I am afraid if I try to run both meters off of just 1 isolation converter, the high voltage will get back to 12 volts on the isolated side and blow the dc-dc converter. I know the traction pack side will work because that was the first meter that was hooked up before I found out that they were not isolated meters and smoked them when hooking up the low voltage side originally.

On to fastening down the loom in the engine compartment. The wiring runs were straightened out and fastened to the brackets and firewall. I will need to disconnect an inline fuse wire and the tachometer lead to reroute them but other that that, the wiring harness is done. 

WIRING RUNS COMPLETED

Then measurements were taken again and some figuring was done to determine if the battery pack will fit in the space between the motor/transaxle and front firewall. If the pack is placed to the passenger side of the engine compartment, it will fit. the rear passenger side of the car is sitting higher, so it appears that I need some additional weight on that side anyway. I am considering adding cells to both modules to increase the voltage anyway, so will make a smaller module that can go on the driver's side to balance the weight in the rear of the car. A cardboard template was made and it appears it is going to be quite a challenge to get the pack in that space without dissembling it.

I am still working on getting all of the Better Place module cells to hold  under 2.7 volts so I can try charging up to get them all to the same voltage level. The module had been discharged until the lowest cell is 2.5 volts several times but some of the cells have still drifted back to above 2.7 volts.

The speedometer wires from the VSS were connected to the wiring harness in the cabin so once the USB cable is finished, the center console can be installed.

SPEEDOMETER WIRES CONNECTED

To finish the interior, the door panels need removed to be painted and to install new outside window seals, so this was as good of a day as any to start.

DOOR PANEL AND ARM REST REMOVED

The temperature in Ohio has been getting close to 90 deg by afternoon, so it has been quite miserable working on the car, even though a lot of little things have been getting finished. We are going to dinner with my Son and his Fiance, so had to knock off a little early but will continue tomorrow.

Randy